FENCE PANEL CONSTRUCTION: pickets go through the rails and attached with 410 stainless steel, rust free screws.
GATE CONSTRUCTION: pickets go through the rails and attached with 410 stainless steel, rust free screws. Framed on each side of the gate; wider gates (over 6′ single gates, over 12′ double gates) include U-Frame. Welded at every picket-to-rail connection.
NOTE: never dig your post holes in advance of receiving your product(s).
| Residential | Commercial | INDUSTRIAL | |
| Powder Coat Colors | 7 colors to choose from no cost difference | 7 colors to choose from no cost difference | 7 colors to choose from no cost difference |
| Vertical Pickets | 5/8″ sq. x .050″ (thick) Pickets go through maximus rail | 3/4″ sq. x .055″ (thick) Pickets go through maximus rail | 1″ sq. x .062″ (thick) Pickets go through maximus rail |
| Picket Spacing W/O Rings Styles 1, 2, 3, 4, 9 and 10 | 3 13/16 inches | 3 5/8 inches | 3 5/8 inches |
| Picket Spacing with Rings Styles 1, 2, 3, 4, 9 and 10 | 3 3/4 inches | 3 3/4 inches | 3.750 inches |
| Picket Spacing Styles 7 & 8 double pickets | 1 5/8 inches | 1 1/2 inches | 1 1/2 inches |
| Horizontal Rails | 1″ x 1 1/8″ side wall = .082″ (thick) top wall = .062″ (thick) 8 METAL INTERNAL RIBS | 1 1/4″ x 1 3/8″ side wall = .088″ (thick) top wall = .065″ (thick) 8 METAL INTERNAL RIBS | 1 5/8″ x 1 5/8″ side wall = .100″ (thick) top wall = .070″ (thick) 8 METAL INTERNAL RIBS |
| Fence Panel Heights | 3 feet, 3 1/2 feet, 4 feet, 4 1/2 feet, 5 feet, 6 feet | 3 feet, 3 1/2 feet, 4 feet, 4 1/2 feet, 5 feet, 6 feet | 4′, 5′, 6′, 7′, 8′ HEIGHTS |
| *Fence Panel WIDTHS | 6 feet wide only TRIM TO FIT ON-SITE | 6′ wide and *8′ wide TRIM TO FIT ON-SITE | 6′ wide and *8′ wide TRIM TO FIT ON-SITE |
| Single Swing Gate WIDTHS | OPENINGS up to 6 FEET wide FRAMED & WELDED | OPENINGS up to 8 FEET wide FRAMED & WELDED | OPENINGS up to 10 FEET wide FRAMED & WELDED |
| Driveway / Estate Gate WIDTHS | OPENINGS up to 12 FEET wide FRAMED & WELDED | OPENINGS up to 16 FEET wide FRAMED & WELDED | OPENINGS up to 20 FEET wide FRAMED & WELDED |
| Materials | 6005-T5 – 35,000 psi Aluminum Alloy | 6005-T5 – 35,000 psi Aluminum Alloy | 6005-T5 – 35,000 psi Aluminum Alloy |
| Material Origin | 100% Made in the USA | 100% Made in the USA | 100% Made in the USA |
| Warranty | Lifetime Warranty on materials and paint finish | Lifetime Warranty on materials and paint finish | Lifetime Warranty on materials and paint finish |
NOTE: It’s ok to mix and match residential fencing with a commercial or industrial gate. Or, commercial fencing with an industrial gate. This happens often when a home or business needs a large driveway gate.
The aluminum fence panel chart below is just a guide. Do not commit to all of your post holes in advance of receiving your products. Both ends of each fence panel are inserted and “set” within each post so you gain very little, if any, distance in your fence runs with each post. The measurements below are approximate. We strongly recommended that you round up your fence run footage measurements to the next foot. Fence panels can easily be trimmed (the width) on-site. Let’s say you have a 23-foot straight run. Order four 6-foot wide fence panels and then you can trim a foot off one of them on-site, or you can trim 3 inches off of all 4 panels. NOTE: The following does not apply to fence panels with rings / circles added to them because it changes the spacing between the vertical pickets… and the on-center spacing.
POOL FENCE WARNING: Be careful when using this chart if you’re fencing is going around a swimming pool. Most jurisdictions (not all) in the USA require that you have LESS THAN 4 INCHES of spacing between the vertical pickets. This means that you may have to trim some of the fence panels, at each end, on-site (easy to do). However, you need to make sure you have enough length in your fence panels so that if you need to trim the panel at each end, to have less than 4 inches, that you have enough product to do so.
